全国400咨询电话

400-622-8284

网站讲座

职业综述

324212: 汽车翻修工 VEHICLE TRIMMER SKILL LEVEL3

MLTSSL Medium and Long-term Strategic Skills List
STSOL Short-term Skilled Occupation List
ROL Regional Occupation List

Assessing Authority:    TRA

GENERAL SKILLED VISA 189               无资格
State Capital Visa subclass 190 Visa subclass 491
ACT Australian Capital Territory Canberra Yes  Yes
NSW New South Wales Sydney    
NT Northern Territory Darwin  Yes Yes 
QLD Queensland (Offshore list) Brisbane         Yes  
SA South Australia Adelaide Yes Yes
TAS Tasmania (Category 1) Hobart Yes     Yes    
VIC Victoria Melbourne  Yes Yes
WA

Western Australia

(General stream)

Perth                    

 

 

Yes:有资格Occupation may be Eligible

Yes:补充技术清单或特殊情况适用的职业  Occupation in the "Supplementary Skilled List" or "Special Conditions Apply"

Yes:职业不在"State Occupation List"或职业状态为“Closed”,但若满足条件仍有机会申请

?:点击州担保详情查看详情

州担保详情 - ANZSCO 324212

NSW

ACCESS LISTAccess list - NSW Government website  
Status State/Region Type Visa Explanation/Additional Requirements
Closed New South Wales Visa subclass 190  
Open New South Wales Visa subclass 491 (regional)  

 

ACT

ACCESS LISTAccess list - ACT Government website  
Status Explanation

 Closed

You may be eligible to apply for ACT nomination if you meet the nomination criteria. 

 

 

NT

ACCESS LISTAccess list - NT Government website  
Status English Requirements Comments
Open Minimum of IELTS 6 in each band or equivalent  

 

 

SA

ACCESS LISTAccess list - SA Government website  
Availability Explanation Additional Requirements

Open

Available

Nominations Available

Competent English;

This occupation is in the State Occupation List

The State Occupation List is available to all applicants, including international graduates of South Australia. Please review theskilled nomination requirements before applying.

If you are an international graduate of South Australia, you should also review the following page: International graduate occupation and waiver requirements

 

TAS

ACCESS LISTAccess list - TAS Government website  
Status Important Information
Open  

324212 汽车翻修工职业描述 Job description

安装、修理和更换车辆的内部修饰,如座位、套管、地板和门饰板。可能要注册或许可。 
Installs, repairs and replaces the interior trim of vehicles such as seats, linings, floor coverings and door trims.Registration or licensing may be required.Previously referred to in ASCO as:4216-11 Vehicle Trimmer.4216-01 Vehicle Trimmers - Supervisor.
 

324212 汽车翻修工职位别名

324212 车内装璜工 Vehicle Upholsterer

 

 

324212 汽车翻修工技术等级 Skill level

汽车翻修工的技能等级为3ANZSCO Skill Level 3)。

 

324212 汽车翻修工所属职业列表

澳洲STSOL职业列表Short-term Skilled Occupation List

 

324212 汽车翻修工澳洲技术移民职业评估 Skills assessment authority

TRA - 澳大利亚职业技术认证中心 Trades Recognition Australia:大陆技术移民申请的绝大部分职业都是通过该类别评估。TRA移民技术评估类别申请的条件为具有澳洲要提名职业相对等的资格(一般是 AQFIII,IV或 Diploma),至少3年的全职提名职业作经验,近2年内至少1年全职带薪提名职业工作经验。对于在获得等同AQF相关资质之前的工作要获得认可的话, 需之前至少5年提名职业或者提名职业相关全职工作经验。
 

相关职业

324211 车身制造工 Vehicle Body Builder

3242 车身制造工和装饰工

ANZSCO 3242 车身制造工和装饰工职责概述  
• 制造和修理标准生产部件和用于特定用途的车体,安装、修理和更换车辆的内部修饰。VEHICLE BODY BUILDERS AND TRIMMERS manufacture and repair prototype production units and purpose-built vehicle bodies, and install, repair and replace the interior trim of vehicles

ANZSCO 3242 车身制造工和装饰工技能要求 Indicative Skill Level  
• 本单元的大多数职位需要具有与下述资质和经验相当的技术层次。Most occupations in this unit group have a level of skill commensurate with the qualifications and experience outlined below
• 在澳洲:AQF证书3级,包括至少2年的在职培训或AQF证书IV级(ANZSCO技术3级)In Australia: AQF Certificate III including at least two years of on-the-job training, or AQF Certificate IV (ANZSCO Skill Level 3)
• 在新西兰:NNZ资格证4级(ANZSCO技术3级)In New Zealand: NZ Register Level 4 qualification (ANZSCO Skill Level 3)
• 至少3年的工作经验可以代替上述的资格证。At least three years of relevant experience may substitute for the formal qualifications listed above.
• 有时除了资格证外,还需要相关的工作经验和/或在职培训。In some instances relevant experience and/or on-the-job training may be required in addition to the formal qualification
• 可能要注册或许可。Registration or licensing may be required

ANZSCO 3242 车身制造工和装饰工主要职责 Tasks Include   
• 使用成型机、切割和焊接工具创造框架部分。constructing framework sections in metal, wood, fibreglass and other materials using shaping machines and cutting and welding equipment
• 将各部分进行螺栓连接、螺钉固定和焊接以形成完整的框架。bolting, screwing, riveting and welding sections together to form complete frameworks
• 对金属薄板、铝板和增强塑料板进行切割和成型加工,使用手动和电动工具讲起安放于框架内。cutting and shaping panels of sheetmetal, aluminium and reinforced plastic and attaching to frameworks using hand and power tools
• 修改装配线,以满足特定需求。modifying assembly line vehicles to special requirements
• 根据图纸和草图准备新的车辆修饰工作,去除旧的覆盖物和装置,并采取新的测量值。preparing new vehicle trim work according to drawings and sketches, and removing old coverings and fittings from vehicles and taking new measurements
• 选择并切割布料、人造革和皮革,使用重型缝纫机缝和。selecting and cutting pieces of fabric, vinyl and leather and sewing pieces together using heavy-duty sewing machines
• 安装内部的设计,如套管、地板和扶手。installing internal trim in vehicles such as lining, floor coverings and armrests
• 安装门饰板、橡皮垫、门锁和把手。attaching door trims, rubber seals, locks and handles

欢迎加入微信